Why Is My Kansas City Driveway Already Crumbling? The Type 1L Cement Truth
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
My driveway was installed in 2023 and is scaling. Is it definitely a Type 1L problem?
It’s the most likely explanation for driveways installed 2022–2024 that are showing early surface scaling, but not the only possibility. Poor finishing technique (overworking the surface or adding water to the mix during placement), inadequate curing, early salt application, or insufficient air entrainment can all cause similar-looking scaling with traditional cement. The only way to confirm Type 1L involvement is to obtain your original batch/delivery ticket and verify the cement type. Even if Type 1L isn’t confirmed, the damage is real and the remediation options are the same.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
Frequently Asked Questions — Type 1L Cement and Kansas City Concrete
Is Type 1L cement banned for use in Kansas City?
No. Type 1L cement is not banned and meets current ASTM standards for many applications. The concern is specifically for exterior flatwork in freeze-thaw environments with deicing salt exposure — which describes virtually every Kansas City driveway, patio, and sidewalk. The engineering community has increasingly recognized that Type 1L’s performance in these specific conditions is inferior to traditional Type I/II, but no formal prohibition exists. The responsibility currently falls on contractors and homeowners to specify the right product.
My driveway was installed in 2023 and is scaling. Is it definitely a Type 1L problem?
It’s the most likely explanation for driveways installed 2022–2024 that are showing early surface scaling, but not the only possibility. Poor finishing technique (overworking the surface or adding water to the mix during placement), inadequate curing, early salt application, or insufficient air entrainment can all cause similar-looking scaling with traditional cement. The only way to confirm Type 1L involvement is to obtain your original batch/delivery ticket and verify the cement type. Even if Type 1L isn’t confirmed, the damage is real and the remediation options are the same.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
Frequently Asked Questions — Type 1L Cement and Kansas City Concrete
Is Type 1L cement banned for use in Kansas City?
No. Type 1L cement is not banned and meets current ASTM standards for many applications. The concern is specifically for exterior flatwork in freeze-thaw environments with deicing salt exposure — which describes virtually every Kansas City driveway, patio, and sidewalk. The engineering community has increasingly recognized that Type 1L’s performance in these specific conditions is inferior to traditional Type I/II, but no formal prohibition exists. The responsibility currently falls on contractors and homeowners to specify the right product.
My driveway was installed in 2023 and is scaling. Is it definitely a Type 1L problem?
It’s the most likely explanation for driveways installed 2022–2024 that are showing early surface scaling, but not the only possibility. Poor finishing technique (overworking the surface or adding water to the mix during placement), inadequate curing, early salt application, or insufficient air entrainment can all cause similar-looking scaling with traditional cement. The only way to confirm Type 1L involvement is to obtain your original batch/delivery ticket and verify the cement type. Even if Type 1L isn’t confirmed, the damage is real and the remediation options are the same.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
Apply a Penetrating Sealer After Full Cure
A quality penetrating silane/siloxane sealer applied after the 28-day cure period dramatically reduces water penetration — which is the first step in both freeze-thaw damage and salt attack. For Kansas City driveways, reseal every 3–5 years. This applies to all concrete but is especially important for any slab you’re unsure about from a cement-type perspective.
Frequently Asked Questions — Type 1L Cement and Kansas City Concrete
Is Type 1L cement banned for use in Kansas City?
No. Type 1L cement is not banned and meets current ASTM standards for many applications. The concern is specifically for exterior flatwork in freeze-thaw environments with deicing salt exposure — which describes virtually every Kansas City driveway, patio, and sidewalk. The engineering community has increasingly recognized that Type 1L’s performance in these specific conditions is inferior to traditional Type I/II, but no formal prohibition exists. The responsibility currently falls on contractors and homeowners to specify the right product.
My driveway was installed in 2023 and is scaling. Is it definitely a Type 1L problem?
It’s the most likely explanation for driveways installed 2022–2024 that are showing early surface scaling, but not the only possibility. Poor finishing technique (overworking the surface or adding water to the mix during placement), inadequate curing, early salt application, or insufficient air entrainment can all cause similar-looking scaling with traditional cement. The only way to confirm Type 1L involvement is to obtain your original batch/delivery ticket and verify the cement type. Even if Type 1L isn’t confirmed, the damage is real and the remediation options are the same.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
Avoid Early Salt Application
New concrete — regardless of cement type — should not have deicing salt applied during its first full winter. The concrete is still curing and developing its surface hardness. For Type 1L concrete especially, early salt exposure dramatically accelerates surface scaling. Use sand for traction the first winter, and begin sealing after the first full cure cycle.
Apply a Penetrating Sealer After Full Cure
A quality penetrating silane/siloxane sealer applied after the 28-day cure period dramatically reduces water penetration — which is the first step in both freeze-thaw damage and salt attack. For Kansas City driveways, reseal every 3–5 years. This applies to all concrete but is especially important for any slab you’re unsure about from a cement-type perspective.
Frequently Asked Questions — Type 1L Cement and Kansas City Concrete
Is Type 1L cement banned for use in Kansas City?
No. Type 1L cement is not banned and meets current ASTM standards for many applications. The concern is specifically for exterior flatwork in freeze-thaw environments with deicing salt exposure — which describes virtually every Kansas City driveway, patio, and sidewalk. The engineering community has increasingly recognized that Type 1L’s performance in these specific conditions is inferior to traditional Type I/II, but no formal prohibition exists. The responsibility currently falls on contractors and homeowners to specify the right product.
My driveway was installed in 2023 and is scaling. Is it definitely a Type 1L problem?
It’s the most likely explanation for driveways installed 2022–2024 that are showing early surface scaling, but not the only possibility. Poor finishing technique (overworking the surface or adding water to the mix during placement), inadequate curing, early salt application, or insufficient air entrainment can all cause similar-looking scaling with traditional cement. The only way to confirm Type 1L involvement is to obtain your original batch/delivery ticket and verify the cement type. Even if Type 1L isn’t confirmed, the damage is real and the remediation options are the same.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
Air Entrainment — Essential for KC Winters
Air-entrained concrete contains millions of tiny air bubbles that provide relief points for freezing water to expand into — dramatically reducing freeze-thaw surface damage. All Kansas City exterior flatwork should use air-entrained concrete with 5–7% air content. This is standard for a knowledgeable KC contractor but is sometimes skipped on “budget” jobs. Confirm it’s in your mix design.
Avoid Early Salt Application
New concrete — regardless of cement type — should not have deicing salt applied during its first full winter. The concrete is still curing and developing its surface hardness. For Type 1L concrete especially, early salt exposure dramatically accelerates surface scaling. Use sand for traction the first winter, and begin sealing after the first full cure cycle.
Apply a Penetrating Sealer After Full Cure
A quality penetrating silane/siloxane sealer applied after the 28-day cure period dramatically reduces water penetration — which is the first step in both freeze-thaw damage and salt attack. For Kansas City driveways, reseal every 3–5 years. This applies to all concrete but is especially important for any slab you’re unsure about from a cement-type perspective.
Frequently Asked Questions — Type 1L Cement and Kansas City Concrete
Is Type 1L cement banned for use in Kansas City?
No. Type 1L cement is not banned and meets current ASTM standards for many applications. The concern is specifically for exterior flatwork in freeze-thaw environments with deicing salt exposure — which describes virtually every Kansas City driveway, patio, and sidewalk. The engineering community has increasingly recognized that Type 1L’s performance in these specific conditions is inferior to traditional Type I/II, but no formal prohibition exists. The responsibility currently falls on contractors and homeowners to specify the right product.
My driveway was installed in 2023 and is scaling. Is it definitely a Type 1L problem?
It’s the most likely explanation for driveways installed 2022–2024 that are showing early surface scaling, but not the only possibility. Poor finishing technique (overworking the surface or adding water to the mix during placement), inadequate curing, early salt application, or insufficient air entrainment can all cause similar-looking scaling with traditional cement. The only way to confirm Type 1L involvement is to obtain your original batch/delivery ticket and verify the cement type. Even if Type 1L isn’t confirmed, the damage is real and the remediation options are the same.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
Option 3: Pursue the Contractor or Material Supplier (If Recent)
If your concrete was installed recently and the contractor knew or should have known about the Type 1L transition, you may have grounds for a warranty or quality claim. The key is documentation: your delivery ticket showing Type 1L was used, photos documenting the damage progression, and any warranty language in your original contract. This is a nuanced legal/industry situation — consult with the contractor first, then with an attorney if needed. The Kansas City contractor community is increasingly aware of this issue, and many reputable contractors are proactively working with affected customers.
How to Protect Your New Concrete from Type 1L Issues Going Forward
Whether you’re getting new concrete poured or helping a neighbor avoid the same issue, here’s what matters in 2025 and beyond:
Specify Cement Type in Your Contract
Ask your contractor explicitly to specify Type I/II Portland cement (not Type 1L / PLC) in the concrete mix design for any exterior flatwork in a freeze-thaw environment. Put it in writing. A reputable contractor will be able to source this — it’s not impossible to get, it just requires being specific with the ready-mix supplier.
Minimum 4,000 PSI Mix
A 4,000 PSI concrete mix (vs. the common 3,000–3,500 PSI) produces a denser concrete that is more resistant to surface scaling from any cause. The water-to-cement ratio in a 4,000 PSI mix is lower, which means less porosity and better freeze-thaw performance. For Kansas City driveways and flatwork, 4,000 PSI should be the minimum.
Air Entrainment — Essential for KC Winters
Air-entrained concrete contains millions of tiny air bubbles that provide relief points for freezing water to expand into — dramatically reducing freeze-thaw surface damage. All Kansas City exterior flatwork should use air-entrained concrete with 5–7% air content. This is standard for a knowledgeable KC contractor but is sometimes skipped on “budget” jobs. Confirm it’s in your mix design.
Avoid Early Salt Application
New concrete — regardless of cement type — should not have deicing salt applied during its first full winter. The concrete is still curing and developing its surface hardness. For Type 1L concrete especially, early salt exposure dramatically accelerates surface scaling. Use sand for traction the first winter, and begin sealing after the first full cure cycle.
Apply a Penetrating Sealer After Full Cure
A quality penetrating silane/siloxane sealer applied after the 28-day cure period dramatically reduces water penetration — which is the first step in both freeze-thaw damage and salt attack. For Kansas City driveways, reseal every 3–5 years. This applies to all concrete but is especially important for any slab you’re unsure about from a cement-type perspective.
Frequently Asked Questions — Type 1L Cement and Kansas City Concrete
Is Type 1L cement banned for use in Kansas City?
No. Type 1L cement is not banned and meets current ASTM standards for many applications. The concern is specifically for exterior flatwork in freeze-thaw environments with deicing salt exposure — which describes virtually every Kansas City driveway, patio, and sidewalk. The engineering community has increasingly recognized that Type 1L’s performance in these specific conditions is inferior to traditional Type I/II, but no formal prohibition exists. The responsibility currently falls on contractors and homeowners to specify the right product.
My driveway was installed in 2023 and is scaling. Is it definitely a Type 1L problem?
It’s the most likely explanation for driveways installed 2022–2024 that are showing early surface scaling, but not the only possibility. Poor finishing technique (overworking the surface or adding water to the mix during placement), inadequate curing, early salt application, or insufficient air entrainment can all cause similar-looking scaling with traditional cement. The only way to confirm Type 1L involvement is to obtain your original batch/delivery ticket and verify the cement type. Even if Type 1L isn’t confirmed, the damage is real and the remediation options are the same.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
Thousands of Kansas City homeowners are watching their brand-new driveways — installed just 2 to 4 years ago — develop alarming surface scaling, pitting, and flaking. Many assume they hired a bad contractor or got low-quality concrete. The real cause is something most homeowners have never heard of: Type 1L Portland-Limestone Cement (PLC), which quietly replaced traditional Type I/II Portland cement at Kansas City-area concrete plants between 2022 and 2024. Here’s what you need to know — and what to do if your concrete is affected.
What Is Type 1L Cement — and Why Did KC Plants Switch?
Portland-Limestone Cement (Type 1L or PLC) is a blended cement that replaces up to 15% of traditional Portland cement clinker with finely ground limestone. It was developed as a lower-carbon alternative to traditional cement — producing about 10% less CO₂ per ton — and was approved for use in the U.S. by ASTM C595 standards in 2012.
The push for wider adoption came from sustainability initiatives and EPA regulatory pressure on cement manufacturers. By 2022–2024, major cement producers began switching their product lines to Type 1L — in many cases, without clearly notifying ready-mix concrete plants, contractors, or end consumers. Kansas City-area concrete plants transitioned to Type 1L during this period. Most contractors continued ordering “standard mix” concrete and received Type 1L without realizing it.
The Problem: Type 1L and Kansas City’s Freeze-Thaw Climate
Type 1L cement performs acceptably in many climates and applications. The problem is specifically in freeze-thaw environments like Kansas City — where the concrete experiences repeated freeze-thaw cycles while simultaneously being exposed to deicing salts (road salt and sidewalk salt).
Kansas City averages 39 freeze-thaw cycles per winter. During each cycle, water enters microscopic pores in the concrete surface, freezes, expands by approximately 9%, and chips away at the paste matrix. Traditional Type I/II Portland cement creates a denser, less permeable surface layer — called the cement paste matrix — that resists this process better.
Type 1L concrete, particularly when finished with any surface water evaporation (a common issue in KC’s variable spring and fall weather), can produce a weaker surface paste matrix. When this weaker matrix meets freeze-thaw cycles and deicing salts, the result is premature surface scaling — the top layer of the concrete literally flakes and peels away, often within the first 1–3 winters.
What Does Type 1L Scaling Look Like?
Type 1L-related surface damage has a distinctive appearance that is different from random cracking or heave damage caused by clay soil:
- Surface flaking or peeling — thin layers of the top surface lifting and coming away
- Pitting — small circular or irregular depressions forming across the surface
- Exposed aggregate — the gravel and sand aggregate becoming visible as the paste matrix above it peels away
- Uniform across the slab — the damage affects the entire surface somewhat evenly, not just cracks or edges
- Accelerating after the first winter — minimal first year, then dramatically worse after the first winter with salt exposure
- Not responsive to sealing — applying a standard sealer slows but doesn’t stop the progression
The Kansas City Connection — Aaron Wingert and FOX4 Coverage
The Type 1L issue in Kansas City gained significant local attention after concrete industry professional Aaron Wingert began documenting and publicizing the connection between the cement switch and premature concrete failures. FOX4 Kansas City covered the story, bringing widespread attention to what had been primarily an industry-insider concern.
Wingert’s documentation showed a clear pattern: driveways and flatwork installed during the 2022–2024 transition period were failing at disproportionate rates, specifically through surface scaling. The timing correlated precisely with the Kansas City-area cement plant transitions to Type 1L.
Many Kansas City contractors were unaware of the cement switch — they ordered “standard mix” and received Type 1L. Many homeowners facing damage claims were left in difficult positions: the concrete met specification on paper, but the real-world performance in KC’s climate was significantly worse than they were led to expect.
Is Your Driveway Affected? How to Check
Step 1: Check the Installation Date
If your concrete was poured between early 2022 and late 2024, and you’re seeing surface scaling or pitting, Type 1L is a likely contributing factor. Concrete poured before 2022 almost certainly used traditional Type I/II cement and would not be affected by this specific issue.
Step 2: Assess the Damage Pattern
Type 1L damage typically appears as surface scaling or pitting across the entire slab surface. If your damage is primarily deep cracking, heaving, or sinking, the more likely culprit is clay soil movement (which affects concrete of any age or type). Both problems can coexist.
Step 3: Get Your Delivery Ticket
If you have your original concrete delivery ticket (also called a batch ticket), it will specify the cement type used in your mix. Look for “Type 1L,” “PLC,” or “Portland-Limestone” on the ticket. If you don’t have it, your contractor should have kept a copy for the project. If the contractor won’t provide it, you can request it directly from the ready-mix concrete supplier if you know which company delivered the concrete.
What Can You Do if Your Concrete Is Scaling from Type 1L?
Option 1: Concrete Resurfacing (If Scaling Is Shallow)
If the scaling is limited to the top ¼ inch or less and the underlying slab is structurally sound (no deep cracking, no heaving or sinking), concrete resurfacing with a polymer-modified overlay can restore the appearance and add surface protection. The overlay bonds to the existing concrete and provides a fresh, durable wearing surface. Cost: $3–$6 per square foot.
Important: resurfacing must be done by a qualified contractor using the right product — not all overlays bond properly to scaled concrete, and a failed overlay bonds the problem in. Get a warranty in writing.
Option 2: Full Replacement (If Scaling Is Deep or Structural Issues Are Present)
If scaling has progressed to expose aggregate, or if the slab also has structural cracking or movement issues, full replacement is typically the right choice. When replacing, ask your contractor specifically: “What cement type will be in the mix?” Current best practice for Kansas City is to specify Type I/II cement (not Type 1L) for all exterior flatwork that will see freeze-thaw cycles and deicing salt exposure. Some contractors are now explicitly writing this into their contracts.
Option 3: Pursue the Contractor or Material Supplier (If Recent)
If your concrete was installed recently and the contractor knew or should have known about the Type 1L transition, you may have grounds for a warranty or quality claim. The key is documentation: your delivery ticket showing Type 1L was used, photos documenting the damage progression, and any warranty language in your original contract. This is a nuanced legal/industry situation — consult with the contractor first, then with an attorney if needed. The Kansas City contractor community is increasingly aware of this issue, and many reputable contractors are proactively working with affected customers.
How to Protect Your New Concrete from Type 1L Issues Going Forward
Whether you’re getting new concrete poured or helping a neighbor avoid the same issue, here’s what matters in 2025 and beyond:
Specify Cement Type in Your Contract
Ask your contractor explicitly to specify Type I/II Portland cement (not Type 1L / PLC) in the concrete mix design for any exterior flatwork in a freeze-thaw environment. Put it in writing. A reputable contractor will be able to source this — it’s not impossible to get, it just requires being specific with the ready-mix supplier.
Minimum 4,000 PSI Mix
A 4,000 PSI concrete mix (vs. the common 3,000–3,500 PSI) produces a denser concrete that is more resistant to surface scaling from any cause. The water-to-cement ratio in a 4,000 PSI mix is lower, which means less porosity and better freeze-thaw performance. For Kansas City driveways and flatwork, 4,000 PSI should be the minimum.
Air Entrainment — Essential for KC Winters
Air-entrained concrete contains millions of tiny air bubbles that provide relief points for freezing water to expand into — dramatically reducing freeze-thaw surface damage. All Kansas City exterior flatwork should use air-entrained concrete with 5–7% air content. This is standard for a knowledgeable KC contractor but is sometimes skipped on “budget” jobs. Confirm it’s in your mix design.
Avoid Early Salt Application
New concrete — regardless of cement type — should not have deicing salt applied during its first full winter. The concrete is still curing and developing its surface hardness. For Type 1L concrete especially, early salt exposure dramatically accelerates surface scaling. Use sand for traction the first winter, and begin sealing after the first full cure cycle.
Apply a Penetrating Sealer After Full Cure
A quality penetrating silane/siloxane sealer applied after the 28-day cure period dramatically reduces water penetration — which is the first step in both freeze-thaw damage and salt attack. For Kansas City driveways, reseal every 3–5 years. This applies to all concrete but is especially important for any slab you’re unsure about from a cement-type perspective.
Frequently Asked Questions — Type 1L Cement and Kansas City Concrete
Is Type 1L cement banned for use in Kansas City?
No. Type 1L cement is not banned and meets current ASTM standards for many applications. The concern is specifically for exterior flatwork in freeze-thaw environments with deicing salt exposure — which describes virtually every Kansas City driveway, patio, and sidewalk. The engineering community has increasingly recognized that Type 1L’s performance in these specific conditions is inferior to traditional Type I/II, but no formal prohibition exists. The responsibility currently falls on contractors and homeowners to specify the right product.
My driveway was installed in 2023 and is scaling. Is it definitely a Type 1L problem?
It’s the most likely explanation for driveways installed 2022–2024 that are showing early surface scaling, but not the only possibility. Poor finishing technique (overworking the surface or adding water to the mix during placement), inadequate curing, early salt application, or insufficient air entrainment can all cause similar-looking scaling with traditional cement. The only way to confirm Type 1L involvement is to obtain your original batch/delivery ticket and verify the cement type. Even if Type 1L isn’t confirmed, the damage is real and the remediation options are the same.
Will my concrete keep getting worse every winter?
Surface scaling from Type 1L (or any cause) typically accelerates during the first 2–3 winters and can reach a stable state once the weaker surface layer has fully spalled away and the more stable underlying concrete is exposed. However, by that point the surface is typically quite rough and pitted — functionally sound but visually unpleasant. If the scaling is still in early stages, acting quickly (applying a penetrating sealer and stopping salt use) can slow the progression.
My concrete contractor says the crumbling is normal weathering. Is that true?
Surface scaling on 1–3 year old concrete is not normal. Well-installed concrete with the correct mix design, air entrainment, and proper finishing should not show significant surface degradation for 20–30+ years under normal Kansas City conditions. If a contractor is telling you that severe scaling on new concrete is normal weathering, get a second opinion from a qualified, independent concrete professional.
Are all Kansas City concrete contractors now aware of the Type 1L issue?
Awareness has increased significantly since the FOX4 coverage and industry discussions around Aaron Wingert’s documentation. Most established Kansas City concrete contractors are now aware of the issue and many are proactively specifying Type I/II cement for exterior flatwork. However, awareness is not universal — particularly among newer or less-experienced contractors. Always ask, and get the answer in writing as part of your contract.
I haven’t seen scaling yet, but my driveway was installed in 2023. Should I be worried?
Not all Type 1L concrete fails prematurely — finishing quality, air entrainment, curing, and site conditions all matter significantly. If your 2022–2024 concrete looks good after 2–3 winters including winters with significant salt exposure, it may have been installed with sufficient care to perform well long-term. Apply a penetrating sealer now if you haven’t, avoid unnecessary salt use, and monitor for any surface changes.
The Bottom Line for Kansas City Homeowners
Kansas City’s concrete market went through a material change — the switch to Type 1L cement — that many homeowners and even many contractors didn’t know was happening. The result is a wave of premature concrete failures across the metro that have caused real financial harm to homeowners who did nothing wrong.
If you’re getting new concrete in 2025 and beyond: ask your contractor what cement type is in the mix, put it in writing, insist on 4,000 PSI minimum with air entrainment, and get a sealer applied after cure. If your existing concrete is scaling: get a copy of your batch ticket, document the damage thoroughly, and talk to a qualified contractor about whether resurfacing or replacement is the right call for your specific situation.
At Best KC Concrete, we were ahead of this issue — we’ve been specifying Type I/II cement for all exterior flatwork and warning our customers about the Type 1L transition since we first identified the problem in our area. If you’re seeing early concrete failure and want an honest assessment of what’s happening and what your options are, contact us for a free consultation.
